Boiled water heating element without PCB board control

Boiled water heater without PCB board

Boiled water heater without PCB board is larger heating area (Tubular Structure), higher power density (100w/cm2), faster temperature ramp up (150℃/S), longer life span (>10,000hours) and better thermal transfer (≥98%).

KSJ 3300w/220v Φ16mm-Instant Type Smart Water Heater is specially designed for water boiler and water dispenser use. Customer can get boiled water about 3 seconds after power supply without Circuit control board, and the water temperature is constant at 95 ℃ plus or minus 2 ℃, this is the ideal electric accessories that to upgrade regular water boiler and water dispenser rapidly to Instant Heater.

Boiled water heater without PCB board makes the temperature ramp up quickly, thermal should be taken away fast. So that we design it in tubular structure, which allow water flow inside tube. The electric heating circuit is made on surface's insulation layers, covered by another insulation layer. Electric and water flow are insulated.

On the basis of the thick film Heating Tube, we develop thick film Heating Element. Boiled water heater without PCB board is made up by water tank, stainless steel thick film heater, plastic shield, interface connectors, thermostats, wire leads etc.

Advantages of boiled water heater without PCB board

Boiled water heater without PCB board is advanced in power density(>100W/cm), quick temperature ramp-up rate(150℃/S) and high thermal transfer(98%). You can get boiling water(≥95℃) in 3 seconds around.

For applications where space is limited, this simple profile heater offers high thermal power density and fast response times to heat up or cool down (due to low thermal mass)
This Electric Heating Element can be matched with thermostats (automatic reset and/or manual reset) and circuit control board.

Thermostat can directly access heating power supply circuit to control it connection or disconnection. Circuit Control Board can adjust the outlet water in multiple temperature levels.

The parameters of boiled water heater without PCB board

Product Model	KSJ1 3300W/220V 16C	Product application	Water dispenser/Water purifier
Product Size	198mm*100mm*46mm	Fixing manner	Fix from sides/Fix from end
Tube Size	030mm*110mm	Water inlet&outlet connector size	Φ10mm
Standard Power/Voltage	3300W(+ 5% ~ -10%)/220V	Lead time	25 Days
Optional power	≤3300W	MOQ	1000 pieces
Electric strength	≥1250V/5mA/60s	Main Components	Heating tube/connector/thermostat, Temp.sensor/sprial column
Bearing Pressure	≤0.2Mpa	Product certification	CQC,ROHS,Wading health approval documents

The most compact instant type heating element is the ideal heating element for novel and fashionable home appliances such as Water Dispenser, Electric Water Faucet, Water Purifier, Coffee Maker, Milk Machine, etc.

Some of our Thick Film Electric Heating Tubes are individual customer solutions which are designed to match our customers` individual and specific requirements. During the development and application stages we work closely together with our customers in a partnership based on trust and mutual confidence.

Boiled water heater without PCB board use precautions

1, The product temperature rising rate is greater than 80 ℃~150℃/S, so, please ensure that the tube is filled with water before use.

2, The pipe must be installed vertically when heating liquid, the direction of liquid flow is from the bottom up. To avoid local dry burning, please add water at first, and then connect to power.
3, Based on different powers, the user should ensure the minimum flow, while ensuring smooth water access to the pipe, so as to avoid vaporization and dry burning.
4, Pay attention to the surface heat dissipation; and due to a big power density, please also pay attention to the rate of heat exchange.

Brief introduction of our Company
Xinxiang jieda precision electronics co., ltd. was established on the year of 2012, and it was located high-tech economic zone of Xinxiang city of Henan province, which is very near to zhengzhou.
During 6 year of development, now Jieda becomes the leading brand in the Thick Film Heating Element field. We are specialize in the in the R&D, manufacture and sale service of stainless steel thick film heating element.
The founders of Jieda spent 7 years and energy on the R&D of thick film printing on curved surface, and over the years, we have been working on the improvement and perfection of this technology to make our products more superior.
In cooperation with well-known household appliance brands, such as Haier, Midea, Kohler and King Clean, the the total sale`s volume exceeded three million pieces. And we hope dyson would be on our partner`s list after further mutual understanding and cooperation. Now Jieda is in the stage of sustainable and healthy development, we hope to cooperate our partner in different application field.